News Center-Sawdust granulator-sawdust granulator-granulator-developed

+86-155-5000-1177

+86-135-7377-3936

 Language

Language

Customer Dynamics

Home page

The importance of the process cooling section of the granulator production line

Regarding the production of biomass particles, each time a whole production line is matched, we need to match the corresponding equipment according to the raw materials. Normally, we need the following sections for a complete granulator production line. From the crushing section of raw materials to the crushing section, the crushed materials are directly entered into the dryer, which can effectively improve the production capacity of the drying equipment. After drying, the materials can be produced within the feeding requirements of the granulator. After the granulator produces granules, it enters the cooling section, and then the cooled granules are packaged. Today, we will talk about the cold in the whole production line.

21

2019

/

02

The maintenance rules of the pressure roller assembly of the biomass pellet machine

When it comes to biomass granulator equipment, we all know that there are many vulnerable parts, including molds, pressure rollers, bearings, etc., but the most vulnerable parts are the pressure roller bearings. In fact, the normal life of the pressure roller bearings of biomass granulator is another 600-800 hours, but many customers need to replace them in 300-400 hours, and even some need to replace them in 200-300 hours. Many of the most important reasons for this are maintenance and oil injection. Due to the harsh environment of the granulation room where the roller bearing is located, the dust in the granulation room will inevitably enter the bearing, and too much bearing dust will lead to butter and bearing connection.

21

2019

/

02

Fuel pellet machine output is affected by those factors

The same fuel pellet machine, the output is large and small, why? The biomass new energy industry is developing rapidly, and the fuel pellet machine has been more and more people are familiar with it. There are also many people who assess the situation and seize the opportunity of this industry to engage in the production of wood pellets. Of course, the quality and standard of the fuel pellet machine produced by different manufacturers are also different. Often many customers bring materials to the manufacturer to test the machine with high output, but if they buy the equipment back for their own production, the output will be too low. Then the problem comes, the same equipment, there is a phenomenon of different output, why? Factors affecting the discharge of the fuel pellet machine 1, the research of the new mold of the pellet machine

21

2019

/

02

Four tips to call your straw pellet machine to increase production and efficiency!

The straw granulator is difficult to discharge, not smooth, and even powder, which makes people have a headache. For example, constipation is disturbing. The words are not pleasant but vivid. Today, Xiao Bian told you four wonderful ways to make your straw granulator no longer constipated: the pressure roller in the 01 straw granulator is an important part in the compression chamber, and it needs continuous rotation to make the material extrude from the die hole under the effect of rolling. However, when the pressure roller is loose, the gap between the pressure roller and the mold will become larger and the pressure will decrease, so naturally it will not be able to discharge smoothly. 02 The motor of the straw granulator needs a certain voltage to work normally. If the voltage is too high

20

2019

/

02

What are the signs before the failure of the sawdust particle machine? And how to solve it

1. After the sawdust particle machine produces particles, it is found that the surface of the particles is uneven and even there are many redundant wounds on the particles. This problem shows that there is a problem with the blade inside the sawdust particle machine. If the blade is in good condition, the surface of the particles produced is very smooth and almost all sizes are due to comparison. 2. The surface of sawdust particles is too smooth, which is also a problem. This can show that the mechanical hard objects are too high, the ring die compression is relatively small, and the compression holes should be increased. This phenomenon is relatively rare, and this kind of problem is rarely encountered. However, it should be avoided as early as possible during construction. The first thing to do is to check the raw materials before construction.

20

2019

/

02

Analysis of the main maintenance of sawdust pellet machine

The maintenance of the sawdust pellet machine is actually very important, and the maintenance can increase the output and extend the service life of the pellet machine. In fact, the maintenance of machinery and equipment is nothing more than regular inspection and regular replacement of useless parts, it is not very tiring things, just because of some cumbersome, most people will be too troublesome and unwilling to do. In fact, scientific and effective maintenance methods can make wood pellet machine high-quality operation, thereby increasing production, only need to spare some time for maintenance can achieve unpredictable results, why not?

20

2019

/

02

< 1...40 41 42...44 >

Picture Name

Copyright © Zhangqiu Fada Pellet Machinery Co., Ltd.

Powered by 300.cn | SEO Tags

Business License